Skip to end of metadata
Go to start of metadata

In this section:

Overview

The SBC Core includes a signaling profile, NNI Profile, in support of the Inter-IMS Network to Network Interface (II-NNI) and interworking of charging parameters for SIP to/from SIP-I/T/GWGW/ISUP calls. The NNI Profile is attached to a ingress SIP trunk group. To learn more about how the SBC performs SIP to SIP-I and SIP-I to SIP interworking based on the NNI Profile, refer to PCV Interworking Enhancement.

Info

The SBC supports up to 32 NNI profiles. 

 

Command Syntax

% set profiles signaling NNIProfile <NNIProfile name>
    additionalPartyCategoryFirst <see values below>
    additionalPartyCategorySecond <see values below> 
    callingPartyCategoryInterworking <disabled | enabled>
    carrierInformationTransfer carrierCategoryAndInfo
        carrierCategory <ciec | iec | olec | scpc | tlec>
        carrierInfo carrierIdCode <4-digit number>
    chargeAreaInformation <5-digit number>
    forwardCallIndicator
        nationalCallIndicator <int | nat>
        originatingIsdnIndicator <non_isdn | isdn>
    historyInfoInterworking <disabled | enabled>

 

To attach the NNIProfile to a SIP Trunk Group, use the following command syntax:

% set addressContext <addressContext name> zone <zone name> sipTrunkGroup <sipTrunkGroup name> signaling NNIProfile <NNIProfile name>

Command Parameters

The NNI Profile parameters are described below:

Table : NNI Profile Parameter Descriptions

Parameter DescriptionLength/RangeParameter Description
NNIProfile1-23 characters

<NNIProfile name>The name of the NNIProfile used to control SBC interworking of charging parameters for SIP to/from SIP-I/T, GW-GW and ISUP calls. The NNI Profile is attached to a SIP trunk group.

 additionalPartyCategoryFirst

N/A

Use this parameter to select one of the following values to specify the first Additional Party Category type. The configured value will be included inside the policy request message sent to the PSX and sent in the ISUP IAM message body of SIP-I/T or over GW-GW message.

  • fixed_1-1
  • fixed_1-2
  • mobile_1-1
  • mobile_1-2
  • mobile_1-3
  • mobile_1-4
  • mobile_1-5
  • mobile_2-1
  • mobile_2-2
  • mobile_2-3
  • mobile_2-4
  • mobile_2-5
  • mobile_2-6
  • mobile_2-7
  • mobile_2-8
  • mobile_2-9
 additionalPartyCategorySecond

N/A

Use this parameter to select one of the above values to specify the second Additional Party Category type. The configured value will be included inside the policy request message sent to the PSX and sent in the ISUP IAM message body of SIP-I/T or over GW-GW message.
callingPartyCategoryInterworkingN/A

Enable this flag to allow the SBC to perform interworking of CallingPartyCategory from SIP to ISUP.

  • disabled (default)
  • enabled
carrierInformationTransfer carrierCategoryAndInfoN/A

Use this parameter to define the carrier poi-category and carrier ID code.

  • carrierCategory – The carrier category type.
    • olec – The SBC inserts the "olec" in the SIP requests in SIP to SIP-I interworking scenarios.
    • tlec – The SBC inserts the "tlec" (terminating carrier info) in the SIP responses in SIP to SIP-I interworking scenarios.
  • carrierInfo carrierIdCode – A 4-digit carrier identification code associated with the charge area. Only ASCII characters from 0 to 9 are valid.

NOTE: The following carrierCategory values are not supported in this release:

    • ciec
    • iec
    • scpc
chargeAreaInformation(ASCII 0-9)A 5-digit value representing the charge area Information that applies to calls establishing the INVITE.
forwardCallIndicator

N/A

Use this object to configure forward call indicator settings.

  • nationalCallIndicator – Choose a National Call Indicator type:
    • int – International call
    • nat – National call
  • originatingIsdnIndicator – Choose an Originating ISDN Access Indicator type:
    • non_isdn
    • isdn
historyInfoInterworkingN/A

Enable this flag to allow the SBC to use HistoryInfo to interwork between SIP and ISUP.

  • disabled (default)
  • enabled