Skip to end of metadata
Go to start of metadata

Use this procedure to change the management IP addresses on SBC 5xx0/5400/7000 platforms once the SBC application is installed.

In following example, all four management IP addresses are changed for an SBC HA pair.

  1. Login to CLI, and check current status of management interfaces:

    > show table system mgmtIpInterfaceGroup mgmtIpInterface
                                                             IP
                          CE      PORT  IP ADDRESS    PREFIX  ADDRESS  PREFIX                                                  RX       TX
    NAME       NAME       NAME    NAME  V4            V4      V6       V6      STATE    NAME       OPER STATUS        IFINDEX  PACKETS  PACKETS
    -------------------------------------------------------------------------------------------------------------------------------------------
    mgmtGroup  mgmtIntf1  MYSBXA  mgt0  10.10.10.111  26      -        -       enabled
               mgmtIntf2  MYSBXA  mgt1  10.10 11.111  26      -        -       enabled
               mgmtIntf3  MYSBXB  mgt0  10.11.12.111  26      -        -       enabled
               mgmtIntf4  MYSBXB  mgt1  10.11.13.111  26      -        -       enabled  mgmtIntf1  resourceAllocated  5        8301     1198618
                                                                                        mgmtIntf2  resourceAllocated  6        3181     6
                                                                                        mgmtIntf3  resourceAllocated  7        8643     1609601
                                                                                        mgmtIntf4  resourceAllocated  8        3185     6
  2. From Configure mode, disable mgmtIntf3 on SBC 'B' server (secondary server):

    > configure
    % set system mgmtIpInterfaceGroup mgmtGroup mgmtIpInterface mgmtIntf3 ceName MYSBXB state disabled
    % commit 
  3. Change IP address of mgmtIntf3 on secondary SBC:

    1. Change IP address:

      % set system mgmtIpInterfaceGroup mgmtGroup mgmtIpInterface mgmtIntf3 ceName MYSBXB ipAddressV4 10.11.22.111 prefixV4 26
      % commit 
    2. Verify change:

      % show system mgmtIpInterfaceGroup mgmtIpInterface mgmtIntf3
      mgmtIpInterfaceGroup mgmtGroup {
          mgmtIpInterface mgmtIntf3 {
              ceName      MYSBXB;
              portName    mgt0;
              ipAddressV4 10.11.22.111;
              prefixV4    26;
              state       disabled;
          }
      }
  4. Enable mgmtIntf3 on secondary SBC:

    1. Enable mgmtIntf3

      % set system mgmtIpInterfaceGroup mgmtGroup mgmtIpInterface mgmtIntf3 ceName MYSBXB state enabled
    2. Verify change:

      % show system mgmtIpInterfaceGroup mgmtIpInterface mgmtIntf3
      mgmtIpInterfaceGroup mgmtGroup {
          mgmtIpInterface mgmtIntf3 {
              ceName      MYSBXB;
              portName    mgt0;
              ipAddressV4 10.11.22.111;
              prefixV4    26;
              state       enabled;
          }
      }
  5. Disable mgmtIntf4 on secondary SBC:

    % set system mgmtIpInterfaceGroup mgmtGroup mgmtIpInterface mgmtIntf4 ceName MYSBXB state disabled
    % commit 
  6. Change IP address of mgmtIntf4 on secondary SBC:

    1. Change IP address:

      % set system mgmtIpInterfaceGroup mgmtGroup mgmtIpInterface mgmtIntf4 ceName MYSBXB ipAddressV4 10.11.32.111 prefixV4 26
      % commit 
    2. Verify change:

      % show system mgmtIpInterfaceGroup mgmtIpInterface mgmtIntf4
      mgmtIpInterfaceGroup mgmtGroup {
          mgmtIpInterface mgmtIntf4 {
              ceName      MYSBXB;
              portName    mgt1;
              ipAddressV4 10.11.32.111;
              prefixV4    26;
              state       disabled;
          }
      }
  7. Enable mgmtIntf4 on secondary SBC

    1. Enable mgmtIntf4:

      % set system mgmtIpInterfaceGroup mgmtGroup mgmtIpInterface mgmtIntf4 ceName MYSBXB state enabled
      % commit 
    2. Verify change:

      % show system mgmtIpInterfaceGroup mgmtIpInterface mgmtIntf4
      mgmtIpInterfaceGroup mgmtGroup {
          mgmtIpInterface mgmtIntf4 {
              ceName      MYSBXB;
              portName    mgt1;
              ipAddressV4 10.11.32.111;
              prefixV4    26;
              state       enabled;
          }
      }
  8. Exit to system-level mode.

    % exit
  9. Perform a switchover:

    > request system admin MYSBX switchover 
  10. Perform a syncStatus command to confirm primary and secondary servers have synced.

    > show table system syncStatus
    SYNC MODULE             STATUS
    ---------------------------------------
    Policy Data             syncCompleted
    Disk Mirroring          syncCompleted
    Configuration Data      syncCompleted
    Call/Registration Data  syncCompleted
  11. Repeat steps 1-7 for mgmtIntf1 and mgmtIntf2 on the SBC 'A' server.