Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
JIRAIDAUTHCHOR-362
REV5UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c99e02c0, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c7f3007b, userName='null'}

Panel

In this section:

Table of Contents
maxLevel4

This describes

Spacevars
0product3
hardware and software requirements and recommendations.

To install and configure

Spacevars
0product3
, make sure the Virtual Machine (VM) host meets the following recommended hardware, server platform and software requirements.

Warning
iconfalse

The recommended hardware and software settings are intended to ensure optimum 

Spacevars
0product3
stability and performance. If the recommended settings are not used, 
Spacevars
0product3
system may not behave as expected.

License Requirements

You must obtain and apply a valid

Spacevars
0product3
 license in order to configure and use the
Spacevars
0product3
. See below:


Multiexcerpt
MultiExcerptNameSBC SWe Lite KVM Hardware
Caption
0Table
1Server Hardware Requirements
Configuration Requirement
Processor2nd Generation Intel Core or Intel Xeon Processor (Sandy bridge or later)
RAM

Each SBC SWe Lite instance requires 1 GiB to 2.5 GiB of RAM depending on your configuration.

Drive Space
Hard disk requirements are dependent upon the number of VMs hosted, the size of each VM at full size, and whether checkpoints will be enabled.
Architecture64-bit Intel processor
Host OS
Red Hat Enterprise Linux 7.2 or newer

 

Info

The SBC SWe Lite does not support execution within a KVM hypervisor cluster.

 

BIOS Setting Recommendations

Sonus recommends the following BIOS settings for optimum performance:

Caption
0Table
1Recommended BIOS Settings for Optimum Performance
BIOS ParameterRecommended
Setting
Details
Intel VT-x (Virtualization Technology)EnabledFor hardware virtualization
Intel Hyper-ThreadingEnabled 
Note
iconfalse

BIOS settings and recommendations must not be changed once it is applied on the server.

Sonus Recommendations for
Spacevars
0series3

General Recommendations

  • Plan enough resources (RAM, CPU, NIC ports, hard disk, etc.) for all the virtual machines (VMs) to run on the server, including resources needed by the host server.
  • Allocate each VM with only as much virtual hardware as that VM requires. Provisioning a VM with more resources than it requires can, in some cases, reduce the performance of that VM as well as other virtual machines sharing the same host.
  • Disconnect or disable any physical hardware devices (Floppy devices, Network interfaces, Storage controllers, Optical drives, USB controllers, etc.) under BIOS settings that you will not be using to free up interrupt/CPU resources.

 

Caption
0Table
1VM Configuration Recommendations
Setting 
vCPU1, 2, and 4 supported
RAM

1 GiB (1024 MiB) to support 1 vCPU

1.5 GiB (1536 MiB) to support 2 vCPUs

2.5 GiB (2560 MiB) to support 4 vCPUs

vNIC

5

(Up to 3 may be disabled, if only a single vNIC is required for media. Note: One vNIC is mandatory for management.)

Virtual Hard Disk5 GiB minimum

Additional Information

  • Minimal networking configuration requires the Management Network Interface and at least one Media Interface to be assigned.
  • Each SBC SWe Lite VM will use approximately 5 GiB of Virtual Hard Drive space. Drive size is predetermined by the imported image.

 

Info
iconfalse

Refer to Downloading the SBC SWe Lite Package for software download instructions.

Pagebreak