Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 8 Current »

This document describes the recommended procedure for upgrading 

Unable to show "metadata-from": No such page "_space_variables"
to its most current release.

Before You Begin

Recommendations

  • Software upgrades should be performed during off peak hours.
  • Before upgrading or staging an upgrade, its recommended to set all Logging to Error level unless advised by Sonus support. For information about logging, see Supported Logging Levels.

You will need current software maintenance to perform the upgrade.

STOP

Read the release notes for the target

Unable to show "metadata-from": No such page "_space_variables"
software version. The upgrade notes (in particular) contain important information that may be relevant to your 
Unable to show "metadata-from": No such page "_space_variables"
configuration. A newer version of 
Unable to show "metadata-from": No such page "_space_variables"
may have different requirements than the previous version.


  1. Make sure your environment still complies with the 

    Unable to show "metadata-from": No such page "_space_variables"
    requirements and supported platforms.

     The End of Support Announcements for SBC Edge and SWe Lite page has important information regarding platform support for future versions of

    Unable to show "metadata-from": No such page "_space_variables"
    .

  2. You must Backup your Sonus SBC Edge data in the unlikely event that you encounter an issue with your 

    Unable to show "metadata-from": No such page "_space_variables"
    upgrade and need to 'roll back' by downgrading back.

    Sonus recommends renaming the backup filename to indicate the current software version and build number. For example, rename the backup to Sonus SBC 1000/2000-1.3.0-b80.tar.gz if you are currently running a 

    Unable to show "metadata-from": No such page "_space_variables"
    version 1.3.0 build 80.

  3. In the event of new alarms raised after upgrading the
    Unable to show "metadata-from": No such page "_space_variables"
    , ensure you have no outstanding alarms before upgrading the
    Unable to show "metadata-from": No such page "_space_variables"
    . To clear alarm(s), follow the instructions outlined in Acting on Displayed Alarms.
  4. If you encounter any problems with your production upgrade that you cannot resolve in a timely manner, create an issue at our support site so we can assist you.

 

Performing the Upgrade

Refer to the appropriate upgrade instructions below for your 

Unable to show "metadata-from": No such page "_space_variables"
hardware configuration:

Starting in Release 5.0, Sonus ASM will be using Windows Server 2012R2 in order to prepare for Skype for Business SBA.

Prepare to Upgrade the
Unable to show "metadata-from": No such page "_space_variables"
with a Built-in ASM

To ensure the Sonus SBC 1000/2000 can communicate with the ASM, you must always upgrade the SBC Communication Service before upgrading the Sonus SBC 1000/2000 software.

The ASM may become unavailable if you upgrade the Sonus SBC 1000/2000 firmware before upgrading the ASM SBC Communication Service.

Follow these steps to upgrade the SBC Communication Service:

  1. From the Sonus SBC Edge Download Center, download the SBC Communication Service update — file name uxcommsvc-release-A.B.C.zip, where A.B.C refers to the version you are upgrading to.
  2. Open the .zip file and unpack it to a temporary folder. This will produce a Setup.msi file.
  3. Apply this SBC Communication Service update by following the instructions outlined in Installing an ASM Package.
  4. To ensure the SBC Communication Service was properly updated, verify the Sonus SBC 1000/2000 Communication Service Version has changed to the intended version.

You now may proceed with upgrading the

Unable to show "metadata-from": No such page "_space_variables"
; follow the instructions below.

Upgrade the
Unable to show "metadata-from": No such page "_space_variables"

  1. From the Sonus SBC Edge Download Center, download the sw-release-x.y.zfile where x.y.z indicates the version number you are upgrading to:
    • Unable to show "metadata-from": No such page "_space_variables"
       Model - the filename uses file extension .img.
    • Unable to show "metadata-from": No such page "_space_variables"
       Model - the filename uses file extension .img.
  2. Select the desired 
    Unable to show "metadata-from": No such page "_space_variables"
    upgrade method:
  3. Ensure the 
    Unable to show "metadata-from": No such page "_space_variables"
    has upgraded by verifying the running SBC Edge software version.

Congratulations, you have completed upgrading the

Unable to show "metadata-from": No such page "_space_variables"
! Proceed to the Upgrading SBC 1000/2000.

 

Post-upgrade Check List

  1. You must clear your web browser cache before you login to the
    Unable to show "metadata-from": No such page "_space_variables"
    .
  2. Perform a backup of your data on the new 
    Unable to show "metadata-from": No such page "_space_variables"
    version. Similarly to the backup preformed in step 3 of the Upgrading SBC 1000/2000 section above, we recommend you rename the backup filename to indicate the current software version and build number.
  3. Ensure there are no new alarms generated after the upgrade. In the event of finding new alarms, address what is causing them.

  • No labels